24/7 emergency service Office Mon to Fri, 8 AM to 5 PM
Heating System Installation in Plainfield, IL

Family-owned · Plainfield Local

4.8 from 53Google reviews

Heating System Installation in Plainfield, IL

Furnaces, heat pumps, and boilers sized right for Chicagoland winters, installed by a family-owned team with 24 years in the trade.

Call or text(815) 609-3150

Request an estimate

Tell us what you need

No obligation · Responds within 1 business day


By submitting this form you agree that we may contact you about your request and share your name and email address with partner companies for email marketing. We never share your mobile number or text message consent with third parties or affiliates for marketing or promotional purposes.

carbon monoxide safety work, professional service in Plainfield, IL

Plainfield Heating Installation Done by the Book

Leto Plumbing & Heating, Inc. has installed heating systems in Plainfield for 24 years as a complete job: right-sized equipment, ductwork inspection, permit-ready installation, and a calibrated system before we leave. If your furnace gave out mid-winter or you're replacing aging equipment before it fails, call (815) 609-3150 and we'll walk you through your options the same day.

We install furnaces, heat pumps, boilers, and mini-split systems. Newer subdivisions usually have usable ductwork; older homes often need modifications before a high-efficiency system performs as it should. Every job is different, so contact us for an accurate estimate.

What Chicagoland Winters Demand from Your Heating System

Plainfield sits in a climate zone where heating season runs roughly six months and overnight lows below zero are not unusual.

A furnace undersized by even 10 percent runs continuously on the coldest nights and never fully heats the home. One oversized by 20 percent short-cycles, wears out faster, and leaves rooms uneven. We use Manual J methodology to find the actual BTU requirement, accounting for square footage, insulation, window exposure and orientation, ceiling height, local design temperatures, and the infiltration that Plainfield's typical two-story homes with attached garages add. If a contractor skips this step, ask why.

System Types

Furnace, Heat Pump, or Boiler: Choosing the Right Fit

The right system depends on your existing infrastructure, your fuel costs, and how your home is built.

Most Plainfield homes run gas forced-air furnaces: natural gas is generally the most cost-effective heating fuel in northern Illinois, and most houses built after 1980 already have ductwork. A high-efficiency gas furnace in the 95-plus AFUE range is the right call for most of our replacements. Heat pumps make sense if you also want cooling efficiency, but need a backup heat source for sub-zero temperatures. Boilers and hydronic systems are more common in older homes, and mini-splits fit homes without ductwork or room additions. If a straightforward furnace replacement works, that's what we'll recommend.
Basement furnace and ductwork

Our Process

How a Leto Heating Installation Actually Goes

Assessment and Equipment Selection

Load calculation plus a walk-through of ductwork, thermostat wiring, and venting. We cover fuel options, efficiency tiers, and utility rebates. Nothing is ordered until you understand what you're getting.

Installation and Permit Coordination

We pull the permit with the local building department, remove the old unit, and install the new one. Every duct connection and trunk line is inspected; homes built before 1990 often need updates for modern equipment, and we tell you before the job starts. Venting and gas lines meet current Illinois mechanical codes, and we attend the final inspection.

Testing, Calibration, and Walkthrough

Full operational test: airflow balance, temperature rise across the heat exchanger, gas pressure, combustion air and venting for CO safety, and thermostat calibration. Then a walkthrough of the controls and follow-up heating system maintenance if needed.

Thermostat Setup and System Controls

We calibrate the thermostat to the new system, set up any zoning, and confirm staging on two-stage or modulating equipment. A properly configured thermostat can recover 10 to 15 percent of heating costs compared to a fixed setpoint, and we can add a smart thermostat installation at the same time. We also handle manufacturer warranty registration requirements. Routine heating system maintenance keeps efficiency where it should be.
Thermostat on a wall

Why Plainfield Homeowners Call Leto

24 years in Chicagoland. 4.8 stars across 53 Google reviews. One number to call for plumbing and HVAC both.

Load calculation before every installation
We size every system to your specific home, not a square-footage guess.
Permits pulled and inspections attended
Every job is code-documented. No skipped steps that create liability later.
Ductwork inspected as part of the scope
We verify the existing system can support the new equipment before we start.
Family-owned since 2002, Plainfield-based
Richard Leto and his team are the people who show up, not a dispatch center.
Call the family (815) 609-3150

Get Your Heating System Installed Before the Cold Arrives

Call (815) 609-3150 to schedule a heating system assessment anywhere in Will County and DuPage County. If your old system has already failed, we answer around the clock.

  • ★ 4.8 on Google
  • BBB A+
  • Licensed & insured

Frequently asked questions

Do I need a permit for a furnace replacement in Plainfield, IL?
Yes. The Village of Plainfield requires a mechanical permit, and the work must pass inspection. We file it and attend the inspection. Skipping it can void your equipment warranty and complicate a resale, and a permit trail also keeps your home's furnace repair history clean.
Will I need new ductwork when I replace my heating system?
Not always, but we inspect before assuming. Homes built before 1990 often have ducts sized for older equipment. If we find significant leakage or undersized trunk lines, you get the cost upfront, because leaky ducts negate most of the efficiency you paid for.
How long does a typical heating system installation take?
A standard gas furnace replacement with existing ductwork runs six to eight hours. With ductwork modifications, plan on a full day to a day and a half. Heat pumps with new line sets or electrical work can take two days. You get a realistic timeframe before we start.

Related

Next step

Tell us about the job

Your name, your number and what needs doing. A person from Leto Plumbing & Heating, Inc. gets back to you.

Rather talk now?(815) 609-3150

No obligation · Responds within 1 business day


By submitting this form you agree that we may contact you about your request and share your name and email address with partner companies for email marketing. We never share your mobile number or text message consent with third parties or affiliates for marketing or promotional purposes.